top of page

SUPERLUBE R & H (EPOXY DRY FILM LUBRICANT)

Product Data Sheet

  1. GENERAL PRODUCT DESCRIPTIONA composition of SUPERLUBE in a two pack epoxy – hardener solutions which on mixing and application form a hard, dry, tenacious lubricating film of SUPERLUBE that ends sliding friction, protects the surface from rust and corrosion, resists moisture, high and low temperatures, extreme pressures and will not attract dust and dirt. Ideal as a general purpose lubricant for the most difficult heavy duty environments.

  2. TECHNICAL SPECIFICATION

  3. Solid Contents57%

  4. LubricantSUPERLUBE

  5. Recommended ThinnerSUPERLUBE R&H THINNER

  6. Flash Point (wet)82o F

  7. Viscosity in KU110

  8. ColourDark Grey

  9. DryingAnerobic

  10. Drying Time5 hours

  11. BrushabilityGood

  12. Oil resistanceExcellent

  13. Water resistanceExcellent

  14. Weather resistanceVery Good

  15. Brine resistanceVery Good

  16. Acid resistanceGood

  17. Tensile Shear Strength350 Kg./sq.cm. on Steel

  18. TYPICAL USESCan be applied to any surface. On drying it will form a hard, dry, tenacious film of SUPERLUBE which will not pick up dust, dirt and grit. Its ability to withstand heavy pressure, dust, extreme temperatures, corrosive conditions, acids and chemicals makes it ideal for use not only as a heavy duty lubricant but also for corrosion protection in the most difficult environments. Further, being unaffected by oils it can be used in conjunction with conventional oils and greases.

  19. ADVANTAGES

  20. Can be applied on any surface – metal, wood, plastic, concrete.

  21. Will not get squeezed out under heavy loads.

  22. Wont pick up abrasive dust and dirt.

  23. Protects against salt, acids, alkalies and fumes.

  24. Lubricates efficiently at high temperature.

  25. Lubricates efficiently at low temperature.

  26. Conducts heat and electricity.

  27. Resists extreme weather conditions.

  28. Outlasts conventional lubricants by 10 to 1.

  29. Most economical due to its wide coverage and long life.

  30. Tensile shear Strength of 350 Kg./sq.cm. on steel.

  31. Bond unaffected by oils and hence can be used with oils and greases.

  32. APPLICATIONCLEANING : Good surface preparation before the initial application is essential for adhesion and performance  of SUPERLUBE R&H . Remove grease,  oil, dust and dirt from the area to be coated and dry the surface before the application.MIXING – SUPERLUBE R&H is supplied as a two component mixture. Occasionally, as a result of storage a can will have some separation of clear solvent at the top. When this is noticed, force a rod through the paste to make holes to drain the solvent to the bottom, then stir thoroughly. Mix SUPERLUBE R (resin) with SUPERLUBE H (Hardener) in a proportion of 1:1 in a separate container.

  33. APPLICATION – Apply the mixture with a clean paint brush or by dip, roll, spray or pour. Two coats will give better result. Drying time should be allowed between applications.

  34. DRYING – The length of time required will vary with the thickness of the coating. In general a minimum of 5 hours is required for complete drying and overnight drying should be sufficient. Allow coated surfaces to dry completely before use.

  35. PACKING DETAILS

  36. PACKINGPRODUCT CODE

  37. 1 litre Tins – 2 sets per case070104

  38. 1 litre Tins – 8 sets per case070116

  39. 4 litre Tins – 2 sets per case070404

  40. Note- One set of SUPERLUBE R&H consists of 1 Tins of SUPERLUBE-R (Resin) and 1 Tin of SUPERLUBE-H (Hardener)

bottom of page